BMW Genuine Oil Filter 11427807177

Product Information

For a long engine life: Original BMW Oil Filters clean the oil with outstanding efficiency and protect your BMW engine from damage; ensuring you enjoy the unique dynamics of your BMW in the future as much as you did on the first day. Let your engine breathe: the Original BMW Air Filter provides superior protection from polluted air and enables a clean combustion process – allowing you to enjoy peak performance with reduced fuel consumption and CO2 emissions. Plenty of good air: Original BMW Interior Filters have a particularly high filtering ability due to the combination of a fluidized bed and active coal. This ensures the air in the interior stays clean and free of impurities or micro-particles. Efficient dirt traps: the Original BMW Fuel Filter dependably purifies petrol and diesel and fulfills the high requirements of modern injection systems in BMW engines – for maximum performance for the entire life of the engine. Spire Automotive Limited - Spire Lakeside Limited - Beadles Sidcup Limited - Think One Limited - Hodgson Automotive Limited First, unscrew the oil cap – aka the place you will be pouring the new oil into. Opening this will help all the old oil flow out smoothly. The cap is located right on the top of the engine cover – you can see it unscrewed in the picture below.

You can change out the filter now if you’d like, but I prefer to move onto draining the oil and replacing the filter while the oil is draining since it will take a few minutes. 3. Remove the oil drain plug and drain the oil Tailored perfectly to each BMW engine, Original BMW oil filters are made with synthetic fibres for even greater robustness. They are capable of meeting the demands of synthetic oils and high oil temperatures, with a large filtration area (up to 3,800 sq. cm) that removes great amounts of impurities such as engine sludge and deposits. Even the finest particles - 0.005 millimetres and smaller- are filtered out, leaving only the purest oil and thus being more environmentally friendly as they reduce fuel consumption. Original BMW oil filters are outstanding in their seal quality which prevents impure oil from returning to the oil circuit and in addition protect the engine and extend its service life. Pretty self explanatory here, remove the bolt, with your catch can located underneath it and let it drain. This will usually take 3-4 minutes to get all of it out. While this is happening lets go ahead and replace the oil filter. First, locate the drain plug and remove the cover for it. If you look at the below pictures, the red circle is where the oil drain plug is located if you are looking at the bottom of your car from underneath the front bumper. The second picture shows what the cover looks like – underneath this cover is where the drain plug is.Today we are bringing you a guide on how to perform a BMW E90 oil change. The car in the pictures is a 2006 325i, but the process and general location of oil filter and drain bolt are the same across all E90’s (and E91/92/93’s), including the 328i and 335i, and other models. This guide is also accurate and helpful for E82 128i and 135i oil changes, and E60 5-series oil changes. The following wholly owned group subsidiary companies are all Appointed Representatives of both Group 1 Automotive UK Limited and Barons Autostar Limited in regard to the specified activities in the regulatory disclosure above: The oil should be fully drained so get underneath the car and replace the drain bolt. Make sure you swap out the old crush washer with the new one! Tighten it by hand with a normal wrench – don’t go overkill on it with a torque wrench. Once you locate the cover, remove it by using your finger or a flathead screwdriver to spin the piece of plastic 180 degrees. Pin Pin

Once you have removed the drain plug cover, here is what you should see: Pin 4. Use your 17mm wrench and let the oil drainRemove the oil o-rings and replace them with the new ones. These are a little difficult to remove sometimes – I used a small flat head screwdriver, but be careful doing this one the big o-ring as you do not want to damage the housing or threads. Beadles Aylesford Limited - Barons Automotive Limited - Beadles Medway Limited - Beadles Maidstone Limited - Beadles Dartford Limited - Beadles Coulsdon Limited Here is what the filter and housing should look like with the new filter installed. Pin 6. Screw the oil filter housing on & tighten the drain bolt This is BMW specific so I recommend using the one I linked to, which will work on all E90-93, E82, and E60 cars. Note: you can also try a strap wrench if you have one handy, but my filter cap was so tight a strap wrench wasn’t good enough.

NOTE: the drain plug has a crush washer on it. Your new oil filter kit should have a new crush washer with it – make sure you get rid of the old one and remember to use the new one. 5. Replace the oil filter and oil filter o-ringsPark's of Hamilton act as a non-independent credit broker. We work with a number of carefully selected finance providers and manufacturers who also offer finance.